6440A REV D Norge Washer Parts List

Dryer cycling thermostat (thermostat, gas)

The cycling thermostat with an internal bias heater will continually cycle the heating element off and on to maintain a constant inner temperature in the dryer. This cycling thermostat has a limit of 155 degrees Fahrenheit and a differential of 25 degrees. Meaning that the heating element will cut out at 155 degrees and cycle back on once the internal temperature drops by 25 degrees. This is a genuine OEM part. Please remember to disconnect the power to the dryer before starting the repair.

M series new style coil kit (sub 12001349)

This gas dryer ignition coil set comes with two ignition coils: one three-terminal boost/hold coil, and one two-terminal secondary coil. If there is no heat or your drying time is getting longer, the coils may be bad and will need to be replaced. Once the coils go bad they do not hold the gas valve open properly. Usually only one of them burns out but you should replace them as a set. Both must be operational for the gas valve to open. This is a genuine OEM part. Please remember to disconnect the power to your dryer before starting the repair.

D-shaped knob clip (u clip)

This control knob clip helps secure the timer knob to the shaft allowing you to select the desired setting for your dryer. If the knob has become loose or the clip is missing you will need to replace the clip. This clip is a genuine OEM part, made of metal and is sold individually.

Meat drawer rail - right side (drawer support rail - right side)

This replacement drawer slide rail is for the right-hand side of your refrigerator. This part attaches to the inside wall of your refrigerator to support the sliding crisper drawer. If the rail is broken or the drawer is not sliding properly, you will need to replace the slide rail. You will need a Phillips screwdriver to complete this repair.

Control knob and clip - white (knob and clip asm)

This knob and clip set is an OEM replacement part for your washer or dryer. The knob accepts a D-shaped shaft and is sold individually.

Rear drum bearing kit (rear bearing kit)

This rear drum bearing kit includes one bearing, one ball shaft, one ball bearing, one ball bearing retainer, a small tube of high temperature lubricant, and installation screws. The support bearing helps support the dryer drum to rotate quietly and smoothly during operation. The bearing attaches on the inside of the rear panel of the dryer cabinet. Over time the drum bearing will wear out. This kit will help keep your dryer running as smoothly as possible with as little noise as possible. This is a genuine OEM part. Please remember to disconnect the power before starting your repair.

Front glide kit (sub 306508)

The front glide helps the drum rotate smoothly and quietly while operating. If your dryer will not tumble or is noisy, the glide could be worn down, causing a metal on metal noise, and will need to be replaced. It is recommended to replace both glides at the same time; a rivet tool is required for this installation. This kit includes a blue plastic glide, a brown cork pad, and two metallic rivets. The front drum glide kit is a genuine OEM part. Please remember to disconnect the power to the dryer before starting your repair.

Refrigerator ice and water filter (filter canister)

Middle spray arm kit (manifold)

The middle wash arm rotates and distribute water inside the dishwasher. The kit has been redesigned and the supply tube is now one piece. This spray arm kit comes with an upper spray arm, holder, water supply tube, and a screw. This kit does NOT include the upper support or mount. It must be ordered separately. This is a genuine OEM part. Please remember to shut off the water supply and disconnect power to your dishwasher before starting the repair.

Refrigerator door shelf bin (bin-door, refrig pseudo, 2 lt)

Upper rack wheel with mount (wheel)

This wheel and mount assembly is located on the upper dishwasher rack to allow you to slide the rack in and out easily. They are sold individually; four are usually required for your model. Also known as stationary wheel mount. This is a genuine OEM part.

Upper roller and axle - kit of 4 (dishwasher dishrack roller kit, set of 4. These rollers allow the dishrack to move in and out of the dishwasher.)

The upper roller and axle attach to the upper rack to allow the dishrack to move in and out along the track of the dishwasher. This is a kit includes 4 rollers and 4 axles for your upper rack. If your dish rack is not moving in and out of the dishwasher properly you may have a broken or missing wheel and it will need to be replaced. The rollers and axles are made out of plastic and are white in color. This is a genuine OEM kit.

Drive belt (belt drive)

This dryer drum drive belt is 89.5" long and has four ribs. This part helps spin the drum during the drying cycle.

Lower spray arm (lower spray arm with shields)

Roller shaft (shaft, tumbler roller)

This roller shaft is the axle for the drum support roller, also known as drum roller axle. If your dryer is noisy or will not tumble, you may need to replace the roller shaft. This part is a genuine OEM part. Please remember to disconnect the power supply to your dryer before you start your repair.